No products in the cart.
10” wall hanging cabinet 6U, w/10” PDU-3 shuko, 10” 12-port Patch Panel Cat5e, 10” cantilever shelf
330/310/320 (W/D/H mm)
RAL 7035 (front glass door)
Color: Black
10” wall hanging cabinet 9U, w/10” PDU-3 shuko, 10” 12-port Patch Panel Cat5e, 10” cantilever shelf
330/310/460 (W/D/H mm)
RAL 7035 (front glass door)
Color: Black
10” wall hanging cabinet 12U, w/10” PDU-3 shuko, 10” 12-port Patch Panel Cat5e, 10” cantilever shelf
330/310/590 (W/D/H mm)
RAL 7035 (front glass door)
Color: Black
RJ45 FTP modular plug for Cat5e 8P8C cable,network wire connector
- Clear color.
- Meet or exceed the requirement in the Cat 5e T568 A and T568 B
- Contacts are nickel plated, phosphor bronze with 6 to 50u” gold plate
- Accept 22-26 AWG solid with a insulation diameter of 0.4-0.64 mm
- For standard FTP cable
General description of amp CAT5E cat6 RJ45 UTP 8p8c Modular Plug
1.Category 5E RJ45 UTP Modular Plug
2.Meet or exceed the requirement in the Cat5E T568A and T568B
3.Operation temperature:-40°C to 60°C, Relative humidity:85%(30°C), Air pressure:70-106Kpa
4.Intensity of anti-currency:DC 1,000V(AV,700V), no puncture and flash-over phenomenon in one minute
5.For standard UTP cable
6.Contacts are nickel plated,phosphor bronze with F to 50u ” gold plated
7.Accept 22-26 AWG solid with an insulation diameter of 0.4-0.64 mm
8.Certified category 6 (ISO11801 PL2 CLASS Ea 15M)
Features:
1.Modular Housing and Cover:Crystal plastic
2.Gender: Male
3.RJ45 Contact Life:750 Times Min
4.IDC Life:200 Times Min
5.Type : 8P8C
Contact-8P8C Berylium bronze with 3 to 50u” gold plated
6.Insulation resistance: 250M OHMS Min
7.OD:6.0-9.0mm
Cable management was designed to be used with any patch panels, rack and cabinet mount products. It mounts on standard 19″ racks or cabinets and provides a clean, beautiful and simple means of organizing from small to large bundles of cables and patch cord.
High power 24V 2.5A power supply + power plug.
Recommended for long cable runs with several high power wireless cards.
airFiber 60 GHz Radio System Featuring Wave Technology with True Duplex Gigabit Performance for PtP Links over 12 km Distances
AF60 LR is a 60GHz radio designed for high-throughput connectivity over an extended range. The airFiber 60 LR features the integrated high-gain dish antenna for high speed, long-range performance Point-to-Point (PtP) links. New WaveTechnology enables incredible long-range performance within the 60GHz spectrum.
Includes a built-in Bluetooth management radio for easy setup.
AO+8192-SR
Data rate 10G, 300M reach
850nm laser diode transmitter
SFP MSA package with duplex LC connector
+3.3V single power supply
Digital Diagnostic Monitor Interface
Very low EMI and excellent ESD protection
RoHS compliant products available
Patch panels are used to terminate twisted pair cables in horizontal and vertical cabling and constitute a point of connecting active equipment working in the network. The elements are characterized by high quality of transmission and mechanical parameters.
The RJ45 Module Keystone BKT is used for forming outlets in both flush and surface mounted versions through gitting them adapters also, enables development of modular patch panels for data cabinets.
The RJ45 Module Keystone BKT is used for forming outlets in both flush and surface mounted versions through gitting them adapters also, enables development of modular patch panels for data cabinets.
Patch panels are used to terminate twisted pair cables in horizontal and vertical cabling and constitute a point of connecting active equipment working in the network. The elements are characterized by high quality of transmission and mechanical parameters.
Patch panels are used to terminate twisted pair cables in horizontal and vertical cabling and constitute a point of connecting active equipment working in the network. The elements are characterized by high quality of transmission and mechanical parameters.
The I-37.PAT extraction clamp is intended for suspending self-supporting round cables (3-7mm diameter). The purpose of the lashing brackets is to tension the ADSS cables between the spans. Lashings enable the line to be completed and its tension. Thanks to the removable cable, the handle can be used on all types of brackets.
Characteristics / application:
– Body: high quality thermoplastic material, mechanical resistance and weather conditions, UV resistant
-Wedge: thermoplastic material of high quality and mechanical resistance as well as weather conditions, UV resistant
Handle rope: stainless steel
-Weight: 0.12kg
-Minimum breaking force: 3.6kN
-Wide range of cable dimensions from 3 to 7mm
– Tool-free assembly ensures quick and efficient installation
-Universal fastening carried out using a bracket mounted on a pillar foundation
Product description:
The extraction lug is designed for hanging round self-supporting cables (3-7mm diameter). The purpose of the lashing brackets is to tension the ADSS cables between the spans. Lashings enable the line to be completed and its tension. Thanks to the removable cable, the handle can be used on all types of brackets. The complete handle consists of: – Ropes made of stainless steel Ø2.5mm with a mushroom element for installation in the handle. – A thermoplastic element in the form of a body and internal blocking wedges ensuring resistance to harsh weather conditions.
Application:
• Suspending self-supporting round cables between spans.
Technical data:
- Handle cable: Ø2.5mm stainless steel
- Cable length to the body: 240mm
- Mechanical strength: 3kN
- With range ofcable dimensions: 3mm-7mm
• Insert color: Black - Tool-free assembly ensures quick and efficient installation
- Universal fastening with the use of a bracket mounted on a pillar foundation.
• Body and Wedge: high quality thermoplastic material, mechanical resistance and weather conditions, UV resistant.
The RJ45 Module Keystone BKT is used for forming outlets in both flush and surface mounted versions through gitting them adapters also, enables development of modular patch panels for data cabinets.
The RJ45 Module Keystone BKT is used for forming outlets in both flush and surface mounted versions through gitting them adapters also, enables development of modular patch panels for data cabinets.
The new updated revision of CCR1009 is here. We attempted to combine all the customer feedback and best practice in CCR device manufacturing that we learned over the last three years, since the first CCR1009 devices were launched. Important changes No switch-chip – the device now features only fully independent Ethernet ports each with a direct connection to the CPU, allowing to overcome previous shared 1Gbit limitation from switch-chip ports and utilize full potential of CPU processing power on those ports. Combo-port – a single 1Gbit software interface that has two hardware interfaces – an SFP cage and a Gigabit Ethernet port, allowing you to use any type of connection available to you. It is also possible to switch between both physical interfaces in RouterOS. In an event of disconnect the combo-port provides hardware fail-over feature. 100Mbps SFP support – this is our first device that supports 100BASE-LX/100BASE-SX/100BASE-BX fiber modules, as well as standard 1.25G SFP modules. More throughput – because the ports are now directly connected to the CPU, the new CCR1009 can achieve even higher throughput.
The new updated revision of CCR1009 is here. We attempted to combine all the customer feedback and best practice in CCR device manufacturing that we learned over the last three years since the first CCR1009 devices were launched. Important changes No switch-chip – the device now features only fully independent Ethernet ports each with a direct connection to the CPU, allowing to overcome previous shared 1Gbit limitation from switch-chip ports and utilize the full potential of CPU processing power on those ports. Combo-port – a single 1Gbit software interface that has two hardware interfaces – an SFP cage and a Gigabit Ethernet port, allowing you to use any type of connection available to you. It is also possible to switch between both physical interfaces in RouterOS. In an event of a disconnect, the combo-port provides a hardware fail-over feature. 100Mbps SFP support – this is our first device that supports 100BASE-LX/100BASE-SX/100BASE-BX fiber modules, as well as standard 1.25G SFP modules. More throughput – because the ports are now directly connected to the CPU, the new CCR1009 can achieve even higher throughput. This unit is equipped with a passive cooling enclosure, two heat-pipes and a specially designed heat-sink, so it’s completely silent. It’s powered by an external 24V 2.5A AC/DC adapter and supports power redundancy if you also power it from the PoE input port. The unit also includes an LCD touchscreen, smart card slot, microSD and an SFP+ port for 10G connections.
CCR1009-7G-1C-PC 7x Gigabit Ethernet, 1x Combo port (SFP or Gigabit Ethernet), 9 cores x 1GHz CPU, 1GB RAM, passive cooling case, RouterOS L6 The new updated revision of CCR1009 is here. We attempted to combine all the customer feedback and best practice in CCR device manufacturing that we learned over the last three years, since the first CCR1009 devices were launched. Important changes: No switch-chip – the device now features only fully independent Ethernet ports each with a direct connection to the CPU, allowing to overcome previous shared 1Gbit limitation from switch-chip ports and utilize full potential of CPU processing power on those ports. Combo-port – a single 1Gbit software interface that has two hardware interfaces – an SFP cage and a Gigabit Ethernet port, allowing you to use any type of connection available to you. It is also possible to switch between both physical interfaces in RouterOS. In an event of disconnect the combo-port provides hardware fail-over feature. 100Mbps SFP support – this is our first device that supports 100BASE-LX/100BASE-SX/100BASE-BX fiber modules, as well as standard 1.25G SFP modules. More throughput – because the ports are now directly connected to the CPU, the new CCR1009 can achieve even higher throughput. This unit is equipped with passive cooling enclosure, two heat-pipes and a specially designed heat-sink, so its completely silent. It’s powered by an external 24V 2.5A AC/DC adapter and supports power redundancy if you also power it from the PoE input port.
CCR1016-12G CCR1016-12G is an industrial grade router with a cutting edge 16 core CPU. If you need many millions of packets per second – Cloud Core Router is your best choice. Unit is equipped with 12 x Gigabit Ethernet ports and color touchscreen LCD. The new r2 version has onboard 2GB of RAM, full size USB slot and dual PSU for redundancy!
CCR1016-12S-1S+ CCR1016 is an industrial grade router with a cutting edge 16 core Tilera CPU. If you need many millions of packets per second – Cloud Core Router is your best choice. This model has twelve SFP ports and one SFP+ port for 10G connectivity. It is available in a 1U rackmount case and also has a serial console port, a touchscreen LCD and a USB port. The CCR1016-12S-1S+ comes with redundant power supplies and one RJ45 SFP 10/100/1000M copper module.
CCR1036-12G-4S is an carrier grade router with a cutting edge 36 core Tilera CPU! Unprecedented power and unbeatable performance – this is our new flagship device. Over 20 times faster than our previous top model, the Cloud Core supports throughput of up to 24 million packets per second, or up to 16 gigabits – full wire speed. The device comes in a 1U rackmount case, has four SFP ports, twelve Gigabit ethernet ports, serial console and a USB port. A color touchscreen displays device status, traffic graphs, or provide access to simple configuration options. It has two SODIMM slots, by default it is shipped with 4GB of RAM, but has no memory limit in RouterOS, so will accept and utilize 16GB or more. It comes with power supply and 1U rackmount case.
CCR1036-12G-4S-EM is an industrial grade router with cutting edge 36 core CPU. If you need many millions of packets per second – Cloud Core Router with 36 cores is your best choice. The device comes in a 1U rackmount case, has four SFP ports, twelve Gigabit ethernet ports, a serial console cable, and a USB port. The new r2 version has onboard 8GB of RAM, onboard M.2 slot, full-size USB slot and dual PSU for redundancy!
Our fastest router has now become even better – the new CCR1036-8G-2S+ now has two SFP+ ports for 10G interface support (SFP+ module available separately). It uses the same 36 core Tilera CPU as our other CCR1036 model, and delivers the same performance. The device comes in a 1U rackmount case, has two SFP+ ports, eight Gigabit ethernet ports and serial console port. The new version of CCR1036-8G-2S+ has onboard 4GB of RAM, onboard M.2 slot, full size USB slot and dual PSU for redundancy! Supports both SFP (1.25G) and SFP+ (10G) modules
Our fastest router has now become even better – the new CCR1036-8G-2S+ now has two SFP+ ports for 10G interface support (SFP+ module available separately). It uses the same 36 core Tilera CPU as our other CCR1036 model, and delivers the same performance, but now, ten gigabit links are possible. The device comes in a 1U rackmount case, has two SFP+ ports, eight Gigabit ethernet ports, a serial console cable and a USB port. The CCR1036-8G-2S+ has two SODIMM slots, by default it is shipped with 4GB of RAM, but has no memory limit in RouterOS (will accept and utilize 16GB or more). Also available now, the EM model with 16GB of RAM! Supports both SFP (1.25G) and SFP+ (10G) modules
The circular distance meter (odometer) is a universal measuring tool, commonly used by contractors, appraisers, farmers, real estate agents and the police. The odometer is characterized by intuitive, simple operation, and the lightweight design makes it easy to transport. The device provides measurements at distances up to 9999.9 m. A large, legible meter increases the comfort of reading the distance, thanks to the meter LED backlight we can take measurements at night. The foldable handle allows the odometer to be folded limiting its size during storage or transport.
Characteristics:
• Lightweight design
• Large readable meter
• Large readable meter
• LED meter backlight
• Foldable handle
• Measurements up to 9999.9m
• Foldable handle
• Measurements up to 9999.9m
Data:
• Dimensions unfolded: 870x340x710mm
• Dimensions after folding: 540x360x110mm
• Weight: 400 g
• Weight: 400 g
Elements of the set:
• Transport bag
• Circular meter
Product description:
Clamps / clips are used to tighten tensioned straps to create solid tie wraps in many industries. The cufflinks are made of corrosion-resistant and weatherproof stainless steel. They are an ideal solution for fastening and fastening requiring high strength, strength and durability. The properties of TELCOLINE terminals ensure their long life and resistance to harmful weather conditions, including low and high temperatures, UV radiation. They are resistant to tearing, tolerate heavy loads and vibrations well. Thus, they guarantee reliable fastening without disturbing the construction of columns, masts, trusses or chimneys.
Application:
• Clamping of tensioned straps
. Technical data:
• Sheet thickness: 1.51mm
• Dimensions: 43.21mm x 21.72mm
• Clamp dimensions: 21.43mm x 5.07mm x 12.23mm
• Made of stainless steel.
• Dimensions: 43.21mm x 21.72mm
• Clamp dimensions: 21.43mm x 5.07mm x 12.23mm
• Made of stainless steel.
Product description:
The extraction lug is designed for hanging round self-supporting cables (3-7mm diameter). The purpose of the lashing brackets is to tension the ADSS cables between the spans. Lashings enable the line to be completed and its tension. Thanks to the removable cable, the handle can be used on all types of brackets. The complete handle consists of: – Ropes made of stainless steel Ø2.5mm with a mushroom element for installation in the handle. – A thermoplastic element in the form of a body and internal blocking wedges ensuring resistance to harsh weather conditions.
Application:
• Suspending self-supporting round cables between spans.
Technical data:
- Handle cable: Ø2.5mm stainless steel
- Cable length to the body: 380mm
- Mechanical strength: 3kN
- With range ofcable dimensions: 3mm-7mm
• Insert color: Black - Tool-free assembly ensures quick and efficient installation
- Universal fastening with the use of a bracket mounted on a pillar foundation.
• Body and Wedge: high quality thermoplastic material, mechanical resistance and weather conditions, UV resistant.
The T-PC.2.5 internal connector cleaner is a tool for cleaning optical fiber connectors / sockets.
Thanks to the small dimensions, it is possible to clean hard-to-reach connectors.
The cleaning itself is quick and easy by pressing the device.
Cleaning does not require the use of alcohol. The process itself is done by moving the thread, made of microfiber and having anti-static properties, so that no dirt appears on the connector.
Basic features:
Model: T-PC.2.5-1.5
For connectors: SC, ST, FC (2.5mm)
Performance: up to 750 cleanings
Antistatic properties.
Easy to clean.
Dimensions: 164 x 17.5 x 17.5mm
The T-PC.1.25 internal connector cleaner is a tool for cleaning optical fiber connectors / sockets.
Thanks to the small dimensions, it is possible to clean hard-to-reach connectors.
The cleaning itself is quick and easy by pressing the device.
Cleaning does not require the use of alcohol. The process itself is done by moving the thread, made of microfiber and having anti-static properties, so that no dirt appears on the connector.
Basic features:
Model: T-PC.2.5-1.5
Suitable for connectors: LC (1.25mm)
Performance: up to 750 cleanings
Antistatic properties.
Easy to clean.
Dimensions: 164 x 17.5 x 17.5mm
Patch panels are used to terminate twisted pair cables in horizontal and vertical cabling and constitute a point of connecting active equipment working in the network. The elements are characterized by high quality of transmission and mechanical parameters.
Patch panels are used to terminate twisted pair cables in horizontal and vertical cabling and constitute a point of connecting active equipment working in the network. The elements are characterized by high quality of transmission and mechanical parameters.
The RJ45 Module Keystone is used for forming outlets in both flush and surface mounted versions through gitting them adapters also, enables development of modular patch panels for data cabinets.
Patch panels are used to terminate twisted pair cables in horizontal and vertical cabling and constitute a point of connecting active equipment working in the network. The elements are characterized by high quality of transmission and mechanical parameters.
Crossing panel 10″ Cat5e 12Ports IDC FTP
Patch panels are used to terminate twisted pair cables in horizontal and vertical cabling and constitute a point of connecting active equipment working in the network. The elements are characterized by high quality of transmission and mechanical parameters.
CRS105-5S-FB The Fiberbox is an outdoor switch with five SFP ports, ideal for locations where distance is restricting the use of regular ethernet cables. The device is weatherproof and comes with a hose clamp and zip ties, ready to be installed on high masts and towers. The package also includes the RJ45 SFP (S-RJ01) copper module already preinstalled in the first port, so you can use ethernet in one of the ports already out of the box. If not needed, remove it to have access to all five SFP ports for using with 1.25 Gbit fiber modules.
The Cloud Router Switch 106-1C-5S is a desktop size smart switch, equipped with one Gigabit Ethernet / SFP combo port and five 1.25Gbps SFP cages. The package includes a power supply. Powered by a 400MHz CPU and 128MB RAM, it runs RouterOS with a L5 license and supports 11- 30V power. This product provides a market leading solution for connecting up to six SFP devices.
Cloud Router Switch 112-8G-4S-IN is a “small size low cost” member of our CRS series. It comes with eight Gigabit Ethernet ports and four SFP cages. Our CRS series combines the best features of a fully functional router and a Layer 3 switch, is powered by the familiar RouterOS. All the specific Switch configuration options are available in a special Switch menu, but if you want, ports can be removed from the switch configuration, and used for routing purposes.
CRS112-8P-4S-IN is an eight Gigabit RJ45 port PoE switch, that offers different power output options: autosensing 802.3af/at PoE/PoE+ and Passive PoE, and four SFP ports provide optical fiber connectivity options to support uplinks of up to 1 Gbps. CRS112-8P-4S-IN is equipped with 12 independent switching ports. 28 V 3.4 A power supply is already included in the box. There is secondary DC jack on the back of the enclosure that supports 48-57 V power supply (not included, can be purchased separately). CRS112-8P-4S-IN can power 802.3af/at devices if 48-57 V DC input is used (unit will automatically detect and provide correct power to devices).
Cloud Router Switch 212-1G-10S-1S+IN is new “small size low cost” member of our CRS series. It comes with one Gigabit Ethernet RJ45 port, ten SFP cages and one 10G SFP+ cage, as well as LCD panel and serial port (RJ45). Product includes indoor desktop case and power supply. Special ears are provided for mounting the unit in rack. Our CRS series combines the best features of a fully functional router and a Layer 3 switch, is powered by the familiar RouterOS. All the specific Switch configuration options are available in a special Switch menu, but if you want, ports can be removed from the switch configuration, and used for routing purposes.
The CRS305 is a compact yet very powerful switch, featuring four SFP+ ports, for up to 10 Gbit per port. The device has a 1 Gbit copper ethernet port for management access and two DC jacks for power redundancy. The device is a very sleek and compact metallic case without any fans, for silent operation. The device has a “Dual boot” feature that allows you to choose between two operating systems – RouterOS or SwOS. If you prefer to have a simplified operating system with only switch specific features, use SwOS. If you would like the ability to use routing and other Layer 3 features in your CRS, use RouterOS. You can select the desired operating system from RouterOS, from SwOS or from the RouterBOOT loader settings. All the feature set comes with a disruptive price, providing the best price/performance on the market.
The CRS309-1G-8S+ is a very compact, yet powerful networking switch. It has eight SFP+ slots, supporting up to 10 Gbit modules in each, which results in a total switching capacity of 162 Gbps and a total non-blocking throughput of 81 Gbps.
The device also has dual-core 800 MHz CPU, 512 MB RAM, a management Ethernet port with PoE power input, RS232 serial port, a grounding terminal and is capable of dual boot (choose which operating system you prefer, RouterOS, or SwOS).
The new Cloud Router Switch 317-1G-16S+RM is a rack-mountable manageable switch with Layer3 features, it has 16 SFP+ ports for high performance 10GbE connectivity and a 1GbE copper port for management. CRS317-1G-16S+RM is powered by a next generation switching chip, giving you wire speed performance for all sixteen 10GbE ports with any Ethernet frame size. New features such as hardware-based Spanning Tree Protocol and Link Aggregation (LACP) provide enhanced protection and true professional performance for your demanding network. The unit has dual redundant power supplies and passive cooling case, so it’s completely silent – for hot environments two redundant fans will automatically keep the system cool if needed.
SwOS/RouterOS powered 24 port Gigabit Ethernet switch with two SFP+ ports, wire speed connectivity with several new switching features! It has “Dual boot” feature that allows you to choose which operating system you prefer to use, RouterOS or SwOS. If you prefer to have a simplified switch only OS with more switch specific features, use SwOS. If you are used to Winbox and would like the ability to use routing and other Layer 3 features on some ports in your CRS, boot and use RouterOS. You can select the desired operating system from RouterOS, from SwOS or from the RouterBOOT loader settings. It gives you all the basic functionality for a managed switch, plus more: allows to manage port-to-port forwarding, apply MAC filter, configure VLANs, mirror traffic, apply bandwidth limitation and even adjust some MAC and IP header fields. SFP cage supports both 1.25 Gb SFP and 10 Gb SFP+ modules.
CRS326-24S+2Q+RM
Our fastest switch for the most demanding setups
If you are working with substantial amount of data – like providing Internet access or maintaining a huge data center – this is the perfect upgrade for your setup. CRS326-24S+2Q+RM is our first product with 40 Gbps QSFP+ ports for remarkably fast and stable fiber connection. Overall it has two 40 Gbps QSFP+ ports and twenty four 10 Gbps SFP+ ports, which provides total nonblocking throughput of 320 Gbps and switching capacity of 640 Gbps with forwarding rate of 252 Mpps with most common packets. CRS326-24S+2Q+RM is easy to manage – it has a full size USB port for configuration and dual power supply for redundancy – no unexpected downtime, your clients and colleagues will be thankful! You can choose between our legendary feature-packed RouterOS for booting or a simpler, but still powerful SwOS. If you would like the ability to use routing and other Layer 3 features in your CRS, use RouterOS
CRS328-24P-4S+RM is a 28 independent port switch, it has 24 Gigabit Ethernet ports, which offer different power output options: Passive PoE, low voltage PoE, 802.3af/at (Type 1 “PoE” / Type 2 “PoE+”) with auto-sensing. CRS328-24P-4S+RM comes in a 1U rackmount case with 100-240 V AC 500 W power supply built-in. The device consumes up to 44 W leaving guaranteed 450 W (3×150 W per every 8 Ethernet ports) to power your PoE devices. Each port can provide up to 30 W of power with any power output option you choose.
The CRS328-4C-20S-4S+RM is a 28 independent port switch with a combo group. This device has twenty SFP ports, four SFP+ ports for 10G modules and four combo ports, where you can choose to use SFP or RJ45 ports from the combo group. These ports can also be software selected, so if you have plugged in all eight cables, you can use scripting, to decide which four combo ports will be active. The device comes in a 1U rackmount case with two 100-240 V power supplies with failover functionality. A RJ45 console port is available for management and debugging, and a mode button can be customised to execute any RouterOS commands. The device has a “Dual boot” feature that allows you to choose between two operating systems – RouterOS or SwOS.
CRS354-48G-4S+2Q+RM If you are looking for a single switch that will put your network setup ahead of the curve without costing a fortune, look no further. The new CRS354-48G-4S+2Q+RM is an effective and adaptable rackmount solution for managing networks in demanding and busy environments. With this product we aim to set a new price-performance bar – get more features while spending way less! This powerful switch has 48 x 1G RJ45 ports and 4 x 10G SFP+ ports. There are also 2 x 40G QSFP+ ports for extremely fast fiber connections or linking with other 40 Gbps devices. The total non-blocking throughput is 168 Gbps, switching capacity is 336 Gbps and the forwarding rate reaches 235 Mpps.
The RB260GSP is a small SOHO switch, which features power output on it’s ethernet ports. Ports 2-5 can power other PoE capable devices with the same voltage as applied to the unit (passive PoE over datalines only). The RB260GSP has five Gigabit Ethernet ports and one SFP cage, switching is done by an Atheros Switch Chip. The device is running an operating system designed specifically for MikroTik Switch products – SwOS.
The RB260GS is a small SOHO switch. It has five Gigabit Ethernet ports and one SFP cage powered by an Atheros Switch Chip. Tested and recommended to use with MikroTik SFP modules: S-85DLC05D, S-31DLC20D and S-35/53LC20D (not included) It is powered by an operating system designed specifically for MikroTik Switch products – SwOS. SwOS is configurable from your web browser. It gives you all the basic functionality for a managed switch, plus more: Allows to manage port-to-port forwarding, apply MAC filter, configure VLANs, mirror traffic, apply bandwidth limitation and even adjust some MAC and IP header fields.
Cloud Smart Switch 326-24G-2S+RM is SwOS powered 24 port Gigabit Ethernet switch with two SFP+ ports in 1U rackmount case that provides wire speed connectivity with several new switching features. It gives you all the basic functionality for a managed switch, plus more: allows to manage port-to-port forwarding, apply MAC filter, configure VLANs, mirror traffic, apply bandwidth limitation and even adjust some MAC and IP header fields. SFP cage supports both 1.25 Gb SFP and 10 Gb SFP+ modules.
It is a kit of two pre-paired devices that form a blazing fast AES encrypted wireless connection. Pure plug-and-play: just point the Cubes at one another and power them on!
The 60 GHz frequency is unaffected by the crowded wireless spectrum, it offers high speed and capacity. Traditional 60 GHz devices, however, can have limited connectivity during bad weather. But not the Wireless Wire Cube! It features an automatic 5 GHz backup connection, so you don’t have to worry about any downtime. No need for additional configuration – the 5 GHz backup connection works out-of-the-box! The Cube will take care of your connection at all times.
It can easily cover a distance of 800 meters and reach fiber-like speed. The Сube form-factor has been designed with function and durability in mind. And it attracts less unwanted attention due to its size and shape. The box includes two Cube 60G ac devices that are already paired together, power supplies, PoE injectors and mounting kits for both devices.
Product Details:
The SFP+ Passive cable assemblies are high performance, cost-effective I/O solutions for 10Gb Ethernet and 10G Fiber Channel applications. SFP+ copper modules allow hardware manufactures to achieve high port density, configurability and utilization at a very low cast and reduced power budget. The high-speed cable assemblies meet and exceed Gigabit Ethernet and Fiber Channel industry standard requirements for performance and reliability.
Product Details:
The SFP+ Passive cable assemblies are high performance, cost-effective I/O solutions for 10Gb Ethernet and 10G Fiber Channel applications. SFP+ copper modules allow hardware manufactures to achieve high port density, configurability and utilization at a very low cast and reduced power budget. The high-speed cable assemblies meet and exceed Gigabit Ethernet and Fiber Channel industry standard requirements for performance and reliability.
Product Details:
The SFP+ Passive cable assemblies are high performance, cost-effective I/O solutions for 10Gb Ethernet and 10G Fiber Channel applications. SFP+ copper modules allow hardware manufactures to achieve high port density, configurability and utilization at a very low cast and reduced power budget. The high-speed cable assemblies meet and exceed Gigabit Ethernet and Fiber Channel industry standard requirements for performance and reliability.
Product Details:
The SFP+ Passive cable assemblies are high performance, cost-effective I/O solutions for 10Gb Ethernet and 10G Fiber Channel applications. SFP+ copper modules allow hardware manufactures to achieve high port density, configurability and utilization at a very low cast and reduced power budget. The high-speed cable assemblies meet and exceed Gigabit Ethernet and Fiber Channel industry standard requirements for performance and reliability.
Product Details:
The SFP+ Passive cable assemblies are high performance, cost-effective I/O solutions for 10Gb Ethernet and 10G Fiber Channel applications. SFP+ copper modules allow hardware manufactures to achieve high port density, configurability and utilization at a very low cast and reduced power budget. The high-speed cable assemblies meet and exceed Gigabit Ethernet and Fiber Channel industry standard requirements for performance and reliability.
Available with 24 or 48 RJ45 Gigabit ports, the EdgeSwitch™ delivers robust performance, PoE+ support and intelligent switching for growing networks.
The I-ODWAT-22-O extraction clamp is intended for suspending flat self-supporting cables (with a maximum width of up to 13mm and a height of up to 5mm ).
The purpose of the extraction clamps is to tension the ADSS cables between the spans. The haul-offs enable the line endings and its tensioning to be realized.
Thanks to the extraction part with the opening eye , the handle is universal and can be installed on open or closed brackets.
The complete handle consists of 3 elements made of stainless steel ensuring resistance to harsh weather conditions and UV radiation: Locking body, blocking wedge and Extraction part in the form of an opening ear installed on the bracket.
The purpose of the extraction clamps is to tension the ADSS cables between the spans. The haul-offs enable the line endings and its tensioning to be realized.
Thanks to the extraction part with the opening eye , the handle is universal and can be installed on open or closed brackets.
The complete handle consists of 3 elements made of stainless steel ensuring resistance to harsh weather conditions and UV radiation: Locking body, blocking wedge and Extraction part in the form of an opening ear installed on the bracket.
Application:
• Bracket used for hanging flat cables, among others: for FTTH, FTTx networks
• High wedge grip strength
• Does not damage the outer sheath of the cable
• Compact and compact construction made of high quality stainless steel, mechanical resistance and weather conditions, resistant to weathering UV
• Tool-free assembly ensures quick and efficient installation
• Opened ear of the extraction partTechnical data:
• Weight: 50g
• Handle length: 250mm
• Length of the hauling part: 190mm
• Mechanical strength: 1kN
• A wide range of flat cable dimensions up to 13mm wide and up to 5mm high
• Bracket used for hanging flat cables, among others: for FTTH, FTTx networks
• High wedge grip strength
• Does not damage the outer sheath of the cable
• Compact and compact construction made of high quality stainless steel, mechanical resistance and weather conditions, resistant to weathering UV
• Tool-free assembly ensures quick and efficient installation
• Opened ear of the extraction partTechnical data:
• Weight: 50g
• Handle length: 250mm
• Length of the hauling part: 190mm
• Mechanical strength: 1kN
• A wide range of flat cable dimensions up to 13mm wide and up to 5mm high
Characteristics / application:
– A clamp used for hanging flat cables, e.g. for FTTH, FTTx networks
-High wedge grip strength
– Does not damage the outer sheath of the cable
-Compact and compact construction made of high-grade stainless steel and mechanical resistance as well as weather conditions, UV resistant
-Mechanical strength: 1.2kN
– Wide range of dimensions for flat cables up to 12mm wide and 4mm high –
Handle length : 220mm – Haul length
: 190mm –
Weight: 50g
Handle length : 220mm – Haul length
: 190mm –
Weight: 50g
– Tool-free assembly ensures quick and efficient installation
-Universal fastening carried out using a bracket mounted on a pillar foundation
Characteristics / application:
– A clamp used for hanging flat cables, e.g. for FTTH, FTTx networks
-High wedge grip strength
– Does not damage the outer sheath of the cable
-Compact and compact construction made of high-grade stainless steel and mechanical resistance as well as weather conditions, UV resistant
-Mechanical strength: 1.2kN
– Wide range of flat cable dimensions up to 12mm wide and 4mm high –
Handle length : 280mm – Haul length
: 250mm –
Weight: 70g
Handle length : 280mm – Haul length
: 250mm –
Weight: 70g
– Tool-free assembly ensures quick and efficient installation
-Universal fastening carried out using a bracket mounted on a pillar foundation
Product Details:
Connector Type: shielded RJ45
Cable Form Standard: ANSI/TIA-568B
Cable Type: F/UTP Cat 5e AWG 26 PVC
Sheath Material: PVC
Color: according to the table below
Standards:PN-EN 50173;ISO/IEC 11801; ANSI/TIA-568; IEC 60332-1;RoHS
Product Details:
Connector Type: shielded RJ45
Cable Form Standard: ANSI/TIA-568B
Cable Type: F/UTP Cat 5e AWG 26 PVC
Sheath Material: PVC
Color: according to the table below
Standards:PN-EN 50173;ISO/IEC 11801; ANSI/TIA-568; IEC 60332-1;RoHS
Product Details:
Connector Type: shielded RJ45
Cable Form Standard: ANSI/TIA-568B
Cable Type: F/UTP Cat 5e AWG 26 PVC
Sheath Material: PVC
Color: according to the table below
Standards:PN-EN 50173;ISO/IEC 11801; ANSI/TIA-568; IEC 60332-1;RoHS
Product Details:
Connector Type: shielded RJ45
Cable Form Standard: ANSI/TIA-568B
Cable Type: F/UTP Cat 5e AWG 26 PVC
Sheath Material: PVC
Color: according to the table below
Standards:PN-EN 50173;ISO/IEC 11801; ANSI/TIA-568; IEC 60332-1;RoHS
Product Details:
Connector Type: shielded RJ45
Cable Form Standard: ANSI/TIA-568B
Cable Type: F/UTP Cat 5e AWG 26 PVC
Sheath Material: PVC
Color: according to the table below
Standards:PN-EN 50173;ISO/IEC 11801; ANSI/TIA-568; IEC 60332-1;RoHS
Product Details:
Connector Type: shielded RJ45
Cable Form Standard: ANSI/TIA-568B
Cable Type: F/UTP Cat 5e AWG 26 PVC
Sheath Material: PVC
Color: according to the table below
Standards:PN-EN 50173;ISO/IEC 11801; ANSI/TIA-568; IEC 60332-1;RoHS
Product Details:
Connector Type: shielded RJ45
Cable Form Standard: ANSI/TIA-568B
Cable Type: F/UTP Cat 5e AWG 26 PVC
Sheath Material: PVC
Color: according to the table below
Standards:PN-EN 50173;ISO/IEC 11801; ANSI/TIA-568; IEC 60332-1;RoHS
Frame material: Aluminum
Fan blade material: PBT
Color: black
Voltage: 110/220V
Current: 0.14/0.1AMP
Power Watts: 30.8/22.0
Speed RPM: 2600/3000
Bearing type: Sleeve bearing, ball bearing is optional
Certificate: CE, ROHS, SAA
Installing: fit for wall cabinet, standing racks, fan unit etc.
The T-TACKA-12 fiber optic splice tray (cassette) is an injection molded serial product made of high quality white ABS . The tray consists of two parts, a casing and a hinged lid. The housing is adapted to store fiber optic splices protected by heat shrink splice protectors. The tray can be used in the construction of telecommunications networks based on single- and multi-mode fiber optic cables. The capacity of the tray is 24 welds, at the same time it is possible to use it as a rack of fiber optic pigtails. The product has been designed in a way that allows you to connect the same trays in stacks through hinges for later maintenance and management at distribution points. The product is intended for installation in sleeves, distribution boxes, fiber optic boxes, for this purpose it has 4 mounting holes with a diameter of 4mm on the back wall of the housing.
Features:
1. Management and storage of fiber optic splices in casings
2. For use with single- and multi-mode optical fibers
3. Durable plastic housing and injection molded lid
4.4 holes for mounting the tray
5. Tray capacity 24 welds
6. Possibility to combine trays in stacks via designed hinges
7. Adapted for installation in internal and external joints, cans
7. Adapted for installation in internal and external joints, cans
The remote control for pulling cables made of FRP fiberglass with a diameter of 10 mm and a length of 100 meters placed on a special stand with wheels to facilitate its unfolding. Fiber with high elasticity and resistance to bending and tearing, covered with yellow PE plastic, which has a protective function and provides good sliding properties. The frame is powder coated in blue, equipped with a special “eye” to make it easier to guide the fiber. (photo No. 2). The structure of the stand provides functional transport, storage and use. The end of the fiber ends with a guiding head.
Application:
– Pulling cables and wires between telecommunication chambers
– Pushing cables under roads
– Installations in suspended ceilings
– Cleaning, clearing pipes, culverts, sewage systems
– Inserting cables into casing pipes
Technical data:
– Outer diameter (with cover): 10 mm
– Length: 100 m
– Weight (with a rack): approx. 26 kg
– Weight with packaging: approx. 27 kg
– Max dimensions: 115x45x125 cm
– Wheel diameter: 20 cm
Single-thread FIBERHOME 12J ADSS flat fiber cable designed for overhead installations on spans up to 60 m. The outer shell is made of high density polyethylene (HDPE, black), resistant to UV radiation, and low and high temperatures (from – 40 [° C] to 70 [° C ]). The cable was reinforced with two FRP (Fiber Reinforced Polymer) rods with a diameter of 2 mm, embedded in the outer shell. The centrally placed tube with 12 optical fibers is filled with a hydrophobic gel that protects them against the ingress of water molecules and vibrations. Single-mode G.652D fibers were used, characterized by a reduced “water peak”, and the minimum bending radius for the cable is 60 mm (the possibility of bending only in one plane). In addition, one ripcord was used to facilitate the removal of the outer sheath of the cable,
Data:
– Fiber type: Single
– mode – Fiber type: G.652D
– Fiber quantity: 12
– Number of tubes: 1
– Tube diameter: 2 mm
– FRP bar diameter: 2 mm
– Dimensions: 7.7×3.8 mm (Width x thickness )
– Minimum bending radius (for the cable): 60 mm
– Outer shell: HDPE – black
– Weight: 36 kg / km
– Operating temperature range: from – 40 [° C] to 70 [° C]
– Tensile strength: up to 1 kN
– Crush strength: 3 kN
Application:
– Overhead networks
FIBERHOME 24J ADSS fiber optic cable (12J / T), flat, G.652D
FIBERHOME 24J ADSS flat fiber cable designed for overhead installations on spans up to 60 m. Fiber optic fibers are contained in two loose tubes filled with hydrophobic gel, which protects them against the ingress of water particles and vibrations. The outer shell is made of high density polyethylene (HDPE, black), resistant to UV radiation, and low and high temperatures (from – 40 [° C] to 70 [° C]). The cable was reinforced with two FRP (Fiber Reinforced Polymer) rods with a diameter of 2 mm, embedded in the outer shell. Single-mode G.652D fibers were used, characterized by a reduced “water peak”, and the minimum bending radius for the cable is 90 mm (the possibility of bending only in one plane). In addition, one ripcord was used to facilitate the removal of the outer sheath of the cable,
Data:
– Fiber type: Singlemode
– Fiber type: G.652D
– Fiber quantity: 24
– Number of tubes: 2
– Number of fibers in the tube: 12
– Tube diameter: 2 mm
– FRP bar diameter: 2 mm
– Dimensions: 9.1×3. 8 mm (Width x thickness)
– Minimum bending radius (for the cable): 90 mm
– Outer shell: HDPE – black
– Weight: 39 kg / km
– Operating temperature range: from – 40 [° C] to 70 [° C]
– Tensile strength: up to 1 kN
– Crush strength: 3 kN
Application:
– Overhead networks
FIBERHOME 48J ADSS fiber optic cable, multi-tube (12J / T), diameter 10.7 mm, G.652D, 2.7kN
Fiber optic cable FIBERHOME 48J ADSS (F-ADSS-MT-48J.2.7KN-12F)is a multi-tube construction cable (12 fibers per tube) designed for overhead installations on spans up to 80 meters. It was reinforced with a central FRP rod (Fiber Reinforced Polymer) with a diameter of 2.5 mm and aramid fibers. Single-mode G.652D fibers have been used, which have a reduced “water peak” (Zero Water Peak). The cable is completely dielectric, characterized by high tensile strength (maximum installation stress 2.7kN). The fibers are contained in tubes filled with a hydrophobic gel protecting them against moisture and vibrations. The outer shell is made of high-density HDPE polyethylene (black), resistant to UV radiation, as well as low and high temperatures (from – 30 [° C] to 70 [° C]). In addition, one ripcord was used to facilitate the removal of the outer sheath. In addition to overhead networks, the F-ADSS-MT-48J.2.7KN-12F cable will be successfully used in teletechnical sewage systems.
Data:
Fiber type: Single mode
Fiber type: G.652D
Fiber amount: 48
Number of tubes: 4 (12J / T)
Number of fillers: 2
Outside diameter: 10.7 mm
Minimum bending radius: 110 mm
Type of outer coating: HDPE
Weight: 88 kg / km
Maximum installation stress: 2.7 kN
Crushing strength: 2 kN
Operating temperature: from – 30 [° C] to 70 [° C]
Application:
– Overhead networks (bays up to 80 m)
– Teletechnical sewage system
Used for fixing one 45x45mm element or two 22,5×45 mm elements
The frames allow mounting telecom jacks and electrical sockets
Mounting up to two telecom jacks or one electrical socket
The frame serves as a concealing and fixing element
To be mounted with surface-mounted and flush boxes
Fixing support included
Quick mounting by pressing-in
Color: white
Remote control for pulling cables made of fiberglass FRP with a diameter of 6 mm and a length of 75 meters placed on a special stand to facilitate its development. Fiber with high elasticity and resistance to bending and tearing, coated with yellow PE plastic, which has a protective function and provides good sliding properties. Fiber frame powder-coated in blue, equipped with a manual brake blocking the drum, and a special “eye” to guide the fiber. The design of the stand ensures functional transport, storage and use. Fiber tip ended with a guide head.
Application:
– Pulling cables between telecommunication chambers
– Cable pushing under roads
– Installations in suspended ceilings
– Cleaning, clearing pipes, culverts, sewage systems
– Entering cables into casing pipes
Technical data:
– Dimensions: 56x18x68 cm
– Outer diameter (with cover): 6 mm
– Length: 75 m
– Weight (with frame): approx. 4.2 kg
– Weight including packaging: approx. 4.6 kg
The GFS-32C distribution box has been designed for wall mounting. Made of plastic PC in gray, it provides resistance to low and high temperatures, and UV radiation for outdoor installations. The degree of protection for the device is IP65 (6 – Dustproof protection, 5 – Protection against water jet poured onto the housing from any side). The box is equipped with 12 blind holes (fig . 1,2) . Depending on your needs, it is possible to break specific plugs for fiber optic cables. The inner boxes are equipped with a hinged plate (photo 3) with mounting columns for two PLC splitter housings (1×16 or 1×8) with holes for fiber optic adapters SC / PC, SC / APC, SC / UPC simplex, and LC duplex (fig . 4.5) . Under the plate there are two screw-on fiber optic trays for 12 splices each (photo7.9.9) included in the product range. The device has been adapted to manage and organize fiber optic cables. The GFS-32 distribution box is a suitable solution for building local area networks, broadband FTTx telecommunications systems, and CATV systems.
Data:
– Dimensions: 420x340x130 mm
– Weight: 2.6 kg
– Protection rating: IP65
– Capacity of the welding tray: 12
– Number of trays: 2
– Operating temperature: -25 ° C ~ + 75 ° C
– Color: Gray
– Cable hole diameters: 4x⌀34 mm, 4x⌀28 mm, 4x⌀17 mm.
Accessories included:
– Two splice trays
– Splice shields : 24
– protective tube
– plastic cable ties
– Metal clip (U-bolt clamps)
– Rubber plugs
– screws and plugs for wall mounting
– key to screw the closing cap
The GXW4200 high-density FXS gateway series enables businesses of all sizes to create an easy-to-deploy VoIP solution that takes advantage of Gigabit speeds. These FXS gateways offer the ability to seamlessly connect multiple locations and all devices within an office to any hosted or on premise IP PBX network to make deployments as easy as possible.
The GXW4216/24/32/48 are fully compliant with SIP standard and interoperable with various VoIP systems, analog PBX and phones on the market. It features multiple FXS analog telephone ports, superb voice quality, a suite of telephony functionalities, easy provisioning, flexible dialing plans, advanced security protection and strong performance in handling high volume voice calls. The GXW42XX series gateways offers businesses a cost-effective hybrid IP and analog telephone system that allows them to enjoy the benefits of VoIP communications.
- 16/24/32 FXS ports, GXW4248 includes 2 50-pin Telco connectors
- 1 Gigabit network port
- 132×48 backlit graphic display with support for multiples languages
- 4 SIP server profiles per system, independent SIP account per port
- Designed and tested for full interoperability with leading IP-PBXs, soft-switches and SIP-based environments
- Advanced security protection with SRTP/TLS/HTTPS
The GXW4200 high-density FXS gateway series enables businesses of all sizes to create an easy-to-deploy VoIP solution that takes advantage of Gigabit speeds. These FXS gateways offer the ability to seamlessly connect multiple locations and all devices within an office to any hosted or on premise IP PBX network to make deployments as easy as possible.
The GXW4216/24/32/48 are fully compliant with SIP standard and interoperable with various VoIP systems, analog PBX and phones on the market. It features multiple FXS analog telephone ports, superb voice quality, a suite of telephony functionalities, easy provisioning, flexible dialing plans, advanced security protection and strong performance in handling high volume voice calls. The GXW42XX series gateways offers businesses a cost-effective hybrid IP and analog telephone system that allows them to enjoy the benefits of VoIP communications.
- 16/24/32 FXS ports, GXW4248 includes 2 50-pin Telco connectors
- 1 Gigabit network port
- 132×48 backlit graphic display with support for multiples languages
- 4 SIP server profiles per system, independent SIP account per port
- Designed and tested for full interoperability with leading IP-PBXs, soft-switches and SIP-based environments
- Advanced security protection with SRTP/TLS/HTTPS
T-VF201 is a laser device used for quick and easy testing of fiber optic track continuity.
The device is powered by two AA batteries, or via a power supply.
The device is sold with a protective cover.
Technical data:
Wavelength: 650nm
Output power:> 1mW
Length of test section up to: 5km
Connector: 2.5mm FC and UPC
Power supply: 2xAA
Weight: 80g
Battery life: 100 hours
Battery life: 100 hours
Data:
• Connector type: LC / APC
• Connector type: Duplex
• SM – single-mode
Features:
• High quality
• Low attenuation connectors
• High measurement repeatability
• Quick assembly
- Material: 1.2mm cold rolled steel.
- Color: Black
- Light in weight, uniform distribution.
- Surface finish: Degreasing, phosphoric, water cleaning, electro-static powder coating
- Installation position: level fixed on the mounting rail or cabinet.
MPO-12LC-OM4-5M
● MPO to 12x LC
● MPO Female (without pin)
● MMF, OM4 (50/125μm)
● POLARITY B
● Polish: UPC
● Cable OD: Φ3.0mm
● Breakout: 0.5m
● LSZH
Lenght: 5 meter
Application
Primary (Campus), Secondary (Riser), Tertiary (Horizontal)
IEEE 802.3: 10Base-T; 100Base-T; 1000Base-T
IEEE 802.5 16 MB; ISDN; TPDDI; ATM
Standards
EN 50173-1; EN 50288-2-1
ISO/IEC 11801; IEC 61156-5
TIA/EIA-568-B.2
Flame restistance
LSHF (LSOH): IEC 60754-2; IEC 61034, IEC 60332-1
LSHF -FR(LSFROH): IEC 60332-3-24
Application
Primary (Campus), Secondary (Riser), Tertiary (Horizontal)
IEEE 802.3: 10Base-T; 100Base-T; 1000Base-T;10GBase-T
IEEE 802.5 16 MB; ISDN; TPDDI; ATM
Power over Ethernet (PoE) / PoE+
Standards
EN 50173-1;
ISO/IEC 11801; IEC 61156-5
TIA/EIA-568-B.2
Flame restistance
FRNC (LSHF,LSOH,LSZH) IEC 60754-2; IEC 61034, IEC 60332-1